Centro Barbecue 3000 Safe use User Manual download pdf (Page 4)

ENGLISH

4. Insert the food pusher into the central tube of the wide mouth feed chute. The pusher is

used to guide foods through the multifunctional feed chute and can be removed when

adding liquid or additional foods while the processor is running.

5. To use the large food chute place the foods to be processed into the large opening of the

food chute. Place the multifunctional feed chute with the food pusher in place over the

food and guide the food through the chute.

Important: The large food chute is best used with the slicing/shredding disc in place.

CONTROLS

The controls are located on the front of the base. Press DOUGH,

SLICE/SHRED, or CHOP to select a function (D). (See directions below.)

PULSE/STOP

• ProcessorshouldbestoredinOFFpositionandunpluggedwhennotinuse.

• UsePULSEforshortprocessingtasks.

• ThePULSEbuttonmustbepressedandheldfortheappliancetooperate.Whenreleased

the appliance will stop. Do not use the PULSE button longer than 2 minutes.

• Themotoroftheprocessorrunsaslongasthisbuttonishelddown.Pressthebuttondown

and then release; allow the blades to stop running and the food to fall to the bottom of the

workbowl before pressing again.

• Pulsinggivesbettercontrolwhenchopping,mincing,mixingandblendingfoods.Youcan

controlthesizeofthefoodsfromcoarsetone.

DOUGH, SLICE/SHRED, or CHOP

• WhenthesefunctionsareselectedtheprocessorwillruncontinuouslyuntilthePULSE/STOP

button is pressed.

• Thesespeedsareusedforchopping,blending,dressings,saucesandmakingbatters

and doughs.

HOW TO CHOP IN THE LARGE WORKBOWL

Thechoppingbladeisusedtocoarselyornelychop,mince,mixandpureefoodstoa

smooth consistency. Use the workbowl to chop fresh and cooked fruits and vegetables,

cookedandrawmeats,shandpoultry;tomakesauces,dressingsandsalsas;tomakepastry,

cookie and cracker crumbs.

1. Lock workbowl with post with interlocking safety latch in place into position

(see Illustration B).

2. Hold large chopping blade by center shaft and insert onto center post (E).

Note: The blade attachments are very sharp. Use caution when handling and

storing.

3. Place food in workbowl.

4. Place cover on workbowl and lock into place by rotating cover clockwise

(See Illustration C).

5. Place the multifunctional feed chute and food pusher in place in food chute. Never use

yourngerstodirectfoodthroughchute.

6. Press CHOP button.

Note: Process foods no more than a few seconds at a time. Pulsing produces excellent results

and offers greater control.

7. To add food or liquid while processor is running, remove food pusher and insert through the

multifunctional feed chute. Replace food pusher in chute.

Important: Be sure chopping blade has completely stopped spinning before

removing cover from processor.

8. Whennished,presstheOFF/PULSEbuttonandallowbladestostoprevolvingbefore

removing cover. Twist cover toward ( ) to remove.

9. To unlock workbowl, turn it clockwise toward ( ) and lift off base.

Note: Remove workbowl from appliance before removing blade to prevent food from

leaking through the center opening of the workbowl.

10. Carefully remove chopping blade and empty workbowl.

11. Unplug appliance when not in use.

HOW TO CHOP IN THE SMALL WORKBOWL

The small workbowl is perfect for small chopping and blending.

1. With the large bowl in place ( see steps 1 and 2 under HOW TO CHOP IN THE LARGE

WORKBOWL) without the large cutting blade, insert the small bowl onto the center

postttingthe3tabsontheoutsideofthebowlintothenotchesonthelargebowlthat

willholdthesmallbowlrmlyinplace.

2. Holding the small cutting blade by the white plastic top and keeping

ngersawayfromthecuttingblades,rmlypressthebladesoverthe

center post until the lower blade rests on the bottom of the bowl. (The

notches on the center post should match the openings on the blade

handle.) (F).

HELPFUL TIPS FOR CHOPPING AND BLENDING

• Theprocessorworksveryquickly.

• Watchcarefullytoavoidover-processingfoods.

• ThePULSEbuttonoffersthebestcontrolandresults.

• Forbestresults,processfoodsthatareaboutthesamesize.

• Donotoverloadthebowl.

• Neverwalkawayfromtheprocessorwhileitison.

• Usehotbutneverboilingliquids.

• Donotprocessmorethan3cupsliquidinthelargeworkbowlatonetime.

• Toprocessmeat,usenomorethan2cupsof¾-inchcubesandprocessusingPULSEin

5 second intervals.

• Thelargeworkbowlhasacapacityof18ozforliquidand8cupsfordryfoods;the

small workbowl can process up to 3 cups..

• Useafunnelinsertedintothefeedchutewhenaddingingredientssuchas,oil,our

and sugar.

USING THE DOUGH BLADE

Thisblademakespreparingdoughefcientandtimesaving.

1. This blade does not extend to the outside rim of the workbowl so it cannot incorporate

ourwhenverysmallamountsofourarebeingprocessed.

Note:Usethemetalbladeforpastryandmixturesthatcontainless2cupsofour.

2. Push dough blade down onto center post into workbowl as far as it will go.

3. Insert all the dry ingredients into the workbowl.

4. Place cover on workbowl. Add multi-functional food chute and food pusher. Process to

blend using the DOUGH function button.

5. With appliance running, add liquids through the small food chute.

1 2 3 4 5 ... 15

Comments to this Manuals

No comments

Centro Barbecue 3000 Safe use User Manual Page 4

Comments to this Manuals

Related products and manuals for Barbecues & grills Centro Barbecue 3000 Safe use