Centro Barbecue Stainless 4000B Safe use Use and Care Guide download pdf (Page 13)

Storing Your Grill

Cleaning the Burner Assembly

Follow these instructions to clean and/or replace parts of

burner assembly or if you have trouble igniting grill.

1. Turn gas OFF at control knobs and LP cylinder.

Remove cooking grates and heat diffusers.

3. Remove carryover tubes and burners.

5. Carefully lift each burner up and away from valve openings.

We suggest three ways to clean the burner tubes. Use the one

easiest for you.

(A) Bend a stiff wire (a light weight coat hanger works well)

into a small hook. Run the hook through each burner

tube several times.

(B) Use a narrow bottle brush with a flexible handle (do not

use a brass wire brush), run the brush through each

burner tube several times.

the burner tube and out the burner ports. Check each

port to make sure air comes out each hole.

6. Wire brush entire outer surface of burner to remove food

residue and dirt.

7. Clean any blocked ports with a stiff wire such as an open

paper clip.

8. Check burner for damage, due to normal wear and corrosion

some holes may become enlarged. If any large cracks or

holes are found replace burner.

VERY IMPORTANT: Burner tubes must reengage valve

openings. See illustration at right.

9. Attach electrode to burner.

10. Carefully replace burners.

11. Attach burners to brackets on firebox.

12. Reposition carryover tubes and attach

to burners. Replace heat diffusers and

cooking grates.

CAUTION

• Clean cooking grates.

• Store in dry location.

• When LP cylinder is connected to grill, store outdoors in a

well ventilated space and out of reach of children.

• Cover grill if stored outdoors. Choose from a variety of grill

covers offered by manufacturers.

• Store grill indoors ONLY if LP cylinder is turned off and

disconnected, removed from grill and stored outdoors.

• When removing grill from storage, follow “Cleaning the

Burner Assembly” instructions before starting grill.

Firebox

Carryover

Firebox

burner

bracket

Electrode

SPIDER ALERT!

VALVE

CONTROL PANEL

SPIDER WEBS

INSIDE VENTURI TUBE

If you notice that your grill is getting hard to light or that the

flame isn’t as strong as it should be, take the time to check and

clean the burner tubes.

BURNER

SPIDER AND WEBS

INSIDE BURNER TUBE

Correct

burner-to-valve

engagement

Detach electrode from burner.

NOTE: Removal/Detachment method will depend on the

burner configuration. See different configurations in

illustrations below.

Remove screws

Firebox

Carry

over tube

Firebox burner

bracket

Pry off

electrode with

a flat blade

screwdriver

Electrode

Important: Always ensure that the venturi burner tubes are clean. A

venturi burner tube has a narrow area in which spiders tend to build

nests.

Spiders or small insects have been known to create “flashback”

problems. The spiders spin webs, build nests and lay eggs in the

grill’s venturi tube(s) obstructing the flow of gas to the burner.

The backed-up gas can ignite in the burner tube behind the

control panel. This is known as a flashback and it can damage

your grill and even cause injury.

To prevent flashbacks and ensure good performance the burner

and venturi tube assembly should be removed from the grill

and cleaned before use whenever the grill has been idle for an

extended period.

464323113 • 13

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 67 68

Comments to this Manuals

No comments

Centro Barbecue Stainless 4000B Safe use Use and Care Guide Page 13

Comments to this Manuals

Related products and manuals for Barbecues & grills Centro Barbecue Stainless 4000B Safe use